Active property market around Peckham and Bermondsey, with 800+ new council homes underway and strong buy-to-let refurbishment demand. Southwark falls well within the South London ground Lian Construction covers on a regular basis. For bathroom renovation work in Southwark, that local knowledge means fewer surprises once work is on site and a team that already understands the borough's typical property stock.
Housing stock in Southwark spans several distinct eras. Peckham and the surrounding streets have a good deal of Victorian and Edwardian terraced housing, typical of inner London's rapid nineteenth-century expansion, alongside interwar and postwar low-rise estates. Bermondsey, given its history as a working wharf and warehouse district, has a mix of converted industrial buildings sitting alongside traditional terraces and mid-rise blocks, a pattern common in London's former riverside industrial areas. With 800+ new council homes underway across the borough, there's also a growing share of newer build stock, which brings different maintenance and refurbishment needs than the Victorian terraces nearby, think modern insulation, service runs and warranty considerations rather than solid-wall damp and old timber. For homeowners and landlords, this mix means a wide range of jobs: period property repair and upgrade work on older terraces, conversion and refurbishment work on ex-industrial buildings, and fit-out or snagging work on newer stock. It's a borough where a contractor needs to be comfortable moving between very different building types and ages, sometimes on the same street.
Southwark's property market, particularly around Peckham and Bermondsey, has stayed active for some time, and that shows in the volume of refurbishment and improvement work landlords and owner-occupiers are commissioning. Buy-to-let refurbishment demand is strong: with rental interest firm in these areas, landlords are investing in kitchen and bathroom upgrades, rewiring and general modernisation to keep properties competitive and up to current letting standards. The 800+ new council homes underway across the borough also point to a wider building pipeline locally, which tends to pull more trades and subcontractor activity into the area generally, and can make it harder to get a reliable contractor booked in at short notice. For homeowners, this means it's worth planning refurbishment work with some lead time rather than expecting immediate availability, particularly for larger or structural jobs. For landlords managing multiple units, coordinating between-tenancy refurbishment efficiently matters more here than in quieter markets, since void periods are costly and good contractors are being pulled in several directions by both private and public sector work at once.
Tanking, waterproofing and wet zones
Any area that gets wet regularly needs proper waterproofing behind the tile, not just grout and silicone holding the water back at the surface. We follow the zone approach set out in BS 5385 for tanking: the shower enclosure itself, the floor area immediately around a bath, and a reasonable margin beyond a basin splash zone all get a waterproof membrane, either a liquid tanking system rolled onto boards in several coats or a bonded sheet membrane taped at joints and corners, before any tile adhesive goes on. Shower trays and formed wetroom floors are treated differently. A shower tray sits on a supporting frame or upstand, with the membrane dressed up the surrounding walls and over the tray edge so water can't track behind it, while a true wetroom floor is built to fall towards a linear or point drain, using a tapered former or a screed laid to falls, with the membrane taken up the walls and across the whole floor area, not just around the drain itself. Getting the falls wrong on a wetroom floor is one of the more expensive mistakes to correct after tiling, since standing water pooling away from the drain usually means lifting the floor and starting the build-up again from scratch. We pressure-test or flood-test waterproofing on wetroom floors and shower enclosures before tiling wherever practical, leaving standing water in place for a set period and checking below for any sign of a leak, rather than assuming a membrane has taken without checking it. Finding a pinhole or a poorly sealed corner joint after the tiles are down is a far bigger and more disruptive job than finding it before a single tile has been laid.
Electrics, ventilation and lighting in bathrooms
Bathrooms are a special location under BS 7671, the UK wiring regulations, and the room is divided into zones based on distance from water: zone 0 is inside the bath or shower itself, zone 1 covers the area directly above it up to 2.25 metres, zone 2 extends a further 0.6 metres beyond that, and everywhere outside those areas is treated as zone 3 or unzoned. Fittings need an ingress protection rating suited to the zone they sit in: a shower light typically needs at least IP65 if it's positioned in zone 0 or 1, and standard 13-amp socket outlets aren't permitted within the zoned area at all, other than a shaver socket to BS EN 61558-2-5, which is the reason bathrooms only ever have a dedicated shaver point rather than a normal switched socket near the basin. Mechanical extraction is a Building Regulations Part F requirement, not just good practice, and a bathroom without an openable window to outside air needs a fan ducted out, sized appropriately to the room volume, and in windowless bathrooms it typically needs a timer overrun so it keeps running for several minutes after the light switches off rather than stopping the moment you leave the room. Switch position is worth planning early in a small bathroom too. A standard light switch mounted on the wall inside the room needs to sit outside the zoned area or be a pull-cord type if it's within reach of the bath or shower, which is why older bathrooms often have a ceiling-mounted pull-cord even where a modern wall switch would otherwise be preferred. In a tight ensuite where every wall is close to the bath or shower, this sometimes limits switch position more than people expect, and it's worth confirming with the electrician at first-fix stage rather than after the wall's already been tiled. We coordinate all of this electrical work with a qualified electrician who tests and certifies it, since bathroom electrical work is notifiable under Part P of the Building Regulations, and we build the certification into the handover pack alongside the rest of the job's documentation and photographs.